Návod Auriol IAN 57340 Vreckové hodinky

Návod

LCD sports watch

with altimeter and compass

Instruction manual

Display symbols

N Heading direction

W Alarm ON/OFF

Z Alarm and snooze function

B Low battery

C Compass mode

A Altimeter mode

T Time mode

P Afternoon

c Temperature in Celsius

f Temperature in Fahrenheit

M Maximum memory

m Minimum memory

Safety notes

This electronic appliance must be protected from water and other hazards. It is

not a toy and children should not use it unsupervised.

Startup and setting of watch

Remove the printed foil from the display. Press and hold both A and C together until all

segments on the display are activated simultaneously.

Selection of M/Ft (meters/feet) distance format

After all display segments have activated the "M" symbol on the display will begin to

blink.

Set the format (M=meters/Ft=feet) by pressing C; confirm your setting by pressing A.

Selection of temperature format °C/°F

After setting the distance format the "C" Symbol on the display will begin to blink.

Set the format (°C=Celsius / °F=Fahrenheit) by pressing C; confirm your setting by

pressing A.

Time setting

After setting the temperature format the symbol for 24h time display mode "24H" will

begin to blink on the display.

Set the format to 12H or 24H by pressing C.

Confirm your setting by pressing A.

Now the hours will begin to blink on the display.

Press C to set the time in hours; subsequently press A to confirm your setting.

After setting the time in hours the minutes will begin to blink.

Press C to set the time in minutes; subsequently press A to confirm your setting.

Repeat this process to set the weekday, the month and the day.

Back light

Press B to activate the back light.

Alarm with snooze function

To set the alarm time press and hold A in normal time mode until the hour display for the

alarm begins to blink on the display.

Press C to set the hours; press A to confirm your setting.

After setting the time in hours the minute display will begin to blink.

Press C to set the minutes; press A to confirm your setting.

Immediately after setting the alarm time the alarm may be activated or deactivated by

pressing C. The W and Z symbols indicate that the alarm is activated.

Confirm your setting by pressing A.

The alarm will sound 3 times in 5 minute intervals for 30 seconds. During the snooze

time the Z symbol will blink on the display.

Press C to shut off the alarm.

To view the set alarm time press A in normal time mode to alternate between the alarm

time and the date.

Temperature memory recall and reset

Press C in normal time mode to access the stored maximum and minimum temperature

values.

The temperature memory may be reset by pressing A immediately upon access.

Entering the different modes

Repeatedly press D to access the different modes of operation. The 3 modes are

accessed in the following order: time mode (T), altimeter mode (A), compass

mode (C) and then back to time mode (T).

Digital altimeter (-500m to 9000m or -1600 feet to 29500 feet)

To minimize the effects of air pressure fluctuations the altimeter should always be

checked / adjusted when at a location with a known altitude (for example at sea level).

Setting

Press D to enter altimeter mode (A). The altitude above or below sea level is shown

on the display.

To adjust the altitude press C to enter Trip Timer mode t. Should the timer already be

running, press A to stop the timer.

Press and hold A until the N or D symbol begins to blink.

Press C to choose the upwards distance counter N or the downwards distance

counter D.

For an ascent choose the upwards distance counter; for a descent choose the

downwards distance counter.

Press A to confirm your setting; the first digit of the altitude display will begin to blink.

Press C to set the first digit und confirm your setting by pressing A.

Repeat the process until the desired altitude is set.

To reset the altitude to sea level, press and hold A until 0 appears on the display.

Ascent or descent (trip)

Before beginning your ascent or descent, enter Trip Timer mode t by pressing C.

Press A to start the timer. The timer can be stopped and restarted at any time by

pressing A.

The current rate of ascent or descent will appear in the upper part of the display.

Press C to enter the different functions t (Trip-Timer), d (total altitude gain or loss) and

a (average ascent or descent speed).

To reset (set to zero) the current trip information, first enter Trip Timer Mode t by

pressing C.

Press A to stop the timer and then press and hold A for 3 seconds to reset the data.

If the height above sea level does not change more than 2.5 meters within 5 minutes,

the altimeter will enter energy saving mode. In energy saving mode the height above

sea level will only be measured once per minute. If the height changes more than 5

meters within 1 Minute the watch will exit energy saving mode and the altitude will be

measured once every 2 seconds. Energy saving mode can also be exited by pressing

any button.

Digital Compass

Press D to switch to compass mode (C).

For precise measurements hold the compass level to the ground pointing in the direction

of N.

The compass shows direction in 3 ways:

1. Precise direction with N in degrees,

2. and cardinal readout e.g. South-East (SE) 135°

3. Precise direction of north (SSS),

south (S S S), east (S) and west (S) on the

outer ring.

To conserve battery power the compass will stop

directional measurements 1 minute after the display

appears. Press A to repeat the directional

measurement.

These dots represent the needle of a conventional

compass:

Example: finding north

The symbol (SSS) can be regarded as the tip of an imaginary needle pointing towards

north. The Symbol (S S S) represents the "tail" end of the needle pointing towards south.

Regardless of the orientation of the compass, north and south is always easily identified

with the symbols (SSS) and (S S S).

Calibrating the compass and environmental interference

All compasses, including digital units, use the earths magnetic field and are sensitive to

environmental interference. Distortions of the magnetic field may be caused by various

sources such as large metal objects, electrical appliances, computers, transformers and

high-voltage power lines.

To achieve precise measurements the compass should be calibrated if:

(1) the error message "Err" (for magnetic distortions) appears continuously,

(2) the numeric readout in degrees is in error by more than 10°

(3) the compass is used in a vehicle for the first time; in this case the magnetic distortions

caused by the metallic parts of the vehicle must be compensated.

Calibrating the Compass

Press D to enter the compass function (C). Press and hold A to enter calibration mode

CAL. To start the calibration press C. The outer ring will on the display will be shown and will

slowly turn.

Place the watch on a flat, level surface (keep away from metal objects, electrical appliances,

computers and high-voltage power lines). Turn the watch slowly in clockwise direction until

you have completed two complete 360° turns. The turns do not need to be perfect but both

turns must be completed in the same direction.

Each turn must not last longer than 60 seconds and not less than 20 seconds.

Complete the calibration procedure by pressing C.

Incorrect calibration can result in erroneous readings from the compass. Preform a new

calibration if the readings seem incorrect.

Entering the declination angle for true north

The magnetic declination at any point on the Earth is the angle between the local magnetic

field -- the direction the north end of a compass points -- and true north.

The local declination is given on the map margin as either east declination (plus) or west

declination (minus).

When navigating, the plus declination must subtracted from and the minus declination

added to the direction on the map.

To enter the declination press D to enter the compass function (C). Press and hold A to

enter calibration mode CAL. Press A again to reach the setting for declination "dEC".

Upon reaching the setting for declination the letter "E" (for east) will begin to flash on the

display. Press C to choose E or W (west) declination and press A to confirm your choice.

The declination value in degrees will blink on the display. Press C to enter the value and

press A to confirm your choice.

The declination value entered into the watch will influence the reading on the compass and

needs to be activated ("On") by pressing C. Press A to confirm.

The following example shows the effect of the declination setting:

The direction shown is N10° (10 degrees north).

- If an east adjustment (E) of 30 degrees is entered the current direction will change to NE

(north-east) 40 degrees.

- If a west adjustment (W) of 30 degrees is entered the current direction will change to NW

(north-west) 340 degrees.

Important Information

Compass

The compass should not be used in the immediate vicinity of magnetic objects- for example

other compasses.

The compass should be recalibrated If the error message "Err" appears continuously on the

display.

Hold the compass exactly horizontally to get a precise reading.

Temperature

The temperature shown is measured within the watch. Please note that your body

temperature will therefore influence the reading.

To correctly measure the temperature, take off the watch for 15 to 30 minutes.

Avoid placing the watch in direct sunlight.

Altimeter

All altimeters (except GPS units) show the altitude by measuring the atmospheric pressure.

Changes in local air pressure can therefore affect the altitude reading.

Please check and readjust the altimeter when you are at a location of known altitude or at

sea level.

Intended use

This electronic appliance is intended for time display and the described additional

features. Any other use or modification of the electronic appliance does not comply with

the intended uses. The manufacturer is not liable for damages caused by improper use

or misuse. The device is not intended for commercial use.

In case of errors

Incorrect compass reading

Incorrect calibration and changing external influences (for example a change of location)

may affect the reading.

Precisely follow the instructions on recalibrating the compass.

Error message "Err" is shown when using the compass

External magnetic influences (for example: metal objects, electrical appliances, computers

and high-voltage power lines).

Move to a different location or recalibrate the compass.

Display becomes weaker or shows incorrect readings

The batteries may have run down or the battery contact surface may have become

corroded.

Remove and reinsert the battery or insert a fresh battery.

Blackened display

External temperature too high; the watch may have been exposed to direct sunlight for an

extended duration.

Display shows irregular digits

Remove and reinsert the battery.

Changing the battery CR2032)

Battery replacements must be performed by an expert to avoid damaging the case and the

gaskets.

Disposal of the electronic appliance

This electronic appliance may not be disposed of with normal household waste.

Dispose of the unit at an approved disposal facility or at your local recycling

centre. Please observe the current rules and regulations when disposing of the

appliance. Contact the disposal system if in doubt.

Disposal of the batteries

Please dispose of your batteries properly in containers especially set up at

retailers. Batteries do not belong in household waste. Dispose of the batteries

at an approved disposal facility or at your local recycling centre. Contact the

disposal system if in doubt.

(

Cleaning instructions

Clean the product with a dry, lint-free cloth. A glasses cleaning cloth is ideal.

Warranty

This product has a 3 year warranty. The warranty period starts on the day of purchase

(sales receipt). Within this period we repair any defects due to material or production

fault free of charge. This does not include batteries. For any defects which are due to

improper use, for example in case of dropping, hitting, contact with water, the right to

claim under warranty ceases to apply.

digi-tech ®, Valterweg 27A, D-65817 Eppstein

-1-

G

-2-

-3-

-4-

-5- -6-

-7-

-8- -9-

G G

G

G

G

G

G

G

ATTENTION: Button C is a push

button only. Please do not pull

on or twist the button.

Hodnotenie

Viac o tomto návode

Chápeme, že je pekné mať k svojmu Auriol IAN 57340 Vreckové hodinky papierovú príručku. Návod si môžete kedykoľvek stiahnuť z našej webovej stránky a vytlačiť si ho sami. Ak chcete mať originálnu príručku, odporúčame vám kontaktovať Auriol. Mohli by byť schopní poskytnúť originálny návod. Hľadáte príručku k svojmu Auriol IAN 57340 Vreckové hodinky v inom jazyku? Vyberte si preferovaný jazyk na našej domovskej stránke a vyhľadajte číslo modelu, aby ste zistili, či ho máme k dispozícii.

Technické údaje

Všetky príručky pre Auriol Vreckové hodinky
Ďalšie príručky od Vreckové hodinky

Často kladené otázky o Auriol IAN 57340 Vreckové hodinky

Náš tím podpory vyhľadáva užitočné informácie o výrobkoch a odpovede na často kladené otázky. Ak nájdete v našich často kladených otázkach nejakú nezrovnalosť, dajte nám o tom vedieť pomocou nášho kontaktného formulára.

Súvisiace produkty

Návod

Auriol IAN 91535 Vreckové hodinky

Návod

Auriol IAN 277495 Vreckové hodinky

Návod

Auriol IAN 111121 Vreckové hodinky

Návod

Auriol IAN 86441 Vreckové hodinky

Návod

Auriol IAN 302690 Vreckové hodinky

Návod

Auriol IAN 114474 Vreckové hodinky

Návod

Auriol IAN 93802 Vreckové hodinky

Návod

Auriol IAN 322185 Vreckové hodinky

Súvisiace kategórie