Návod Parkside IAN 360432 Zváračka

Návod

17GB/IE/NI/CY/MT

• Selecting compressed air

supply

Press the selector switch for the compressed

air supply

10

in order to select the com-

pressed air source.

 In INT position (Figure J) the compressed

air supply is provided by the integrated

compressor. In EXT position (Figure K) by

an external compressor.

 When using the integrated compressor,

switch the toggle switch for external

compressed air

18

to the “closed”

position (Figure L).

• Procedure when using an

external compressor

PLEASE NOTE!

For plasma cutting, a pressure of

4–4.5bar is recommended. Adjust this

accordingly on your compressor. Please

bear in mind that the pressure can lower

while setting the air pressure. Thus, in

a hose length measuring 10 m and an

internal diameter of 9 mm it drops by

approx. 0.6 bar.

The compressed air source must have a fi lter

and regulator.

 Connect the compressed air hose

20

on

the back of the plasma cutter

1

to the

compressed air connection

17

. To do so,

insert the side of the compressed air hose

into the compressed air connection

17

of

the plasma cutter

1

without a quick

connector (see Fig. I).

 The pressure can be adjusted using the

pressure regulator on your compressor.

Select a pressure of 4–4.5 bar.

 In order to release the compressed air

hose

20

, you must press the locking

mechanism of the compressed air

connection

17

and pull out the com-

pressed air hose

20

at the same time

(see Fig. I).

 Switch the toggle switch for external

compressed air

18

to the “open” position

(Figure M).

• Connecting the cutting torch

 Insert the plasma burner plug

7

into the

plasma burner connection socket

13

and

tighten the plasma burner plug hand-tight

7

(see Fig. A+B).

 Insert the plasma burner power plug

6

into the plasma burner power socket

11

and tighten the union nut hand-tight

(see Fig. A+B).

• Connecting the ground cable

Connect the ground terminal plug

5

with

the ground terminal - connection socket

12

.

Make sure that the connecting shaft is fi rst

connected and then turned. The connecting

shaft must face upwards when plugging in

the ground cable plug

5

. After plugging in,

the connecting shaft must be rotated in a

clockwise direction until it reaches the stop,

in order to lock it in place (see Fig. A+B).

This does not require force!

• Fitting the removable roller

guide (optional)

Push the removable roller guide

19

over the

nozzle clamping sleeve

8b

, until the locking

screws

19a

are completely above the black

area of the plasma burner

8

(behind the

gap at the back of the nozzle clamping

sleeve

8b

) (see Fig. A+B). Now fi x the

locking screws

19a

. The guide rollers

19c

are

now positioned such that the required

Before use

Hodnotenie

Viac o tomto návode

Chápeme, že je pekné mať k svojmu Parkside IAN 360432 Zváračka papierovú príručku. Návod si môžete kedykoľvek stiahnuť z našej webovej stránky a vytlačiť si ho sami. Ak chcete mať originálnu príručku, odporúčame vám kontaktovať Parkside. Mohli by byť schopní poskytnúť originálny návod. Hľadáte príručku k svojmu Parkside IAN 360432 Zváračka v inom jazyku? Vyberte si preferovaný jazyk na našej domovskej stránke a vyhľadajte číslo modelu, aby ste zistili, či ho máme k dispozícii.

Technické údaje

Všetky príručky pre Parkside Zváračky
Ďalšie príručky od Zváračky

Často kladené otázky o Parkside IAN 360432 Zváračka

Náš tím podpory vyhľadáva užitočné informácie o výrobkoch a odpovede na často kladené otázky. Ak nájdete v našich často kladených otázkach nejakú nezrovnalosť, dajte nám o tom vedieť pomocou nášho kontaktného formulára.

Súvisiace produkty

Návod

Parkside PFDS 33 A1 Zváračka

Návod

Parkside PSGS 120 A1 Zváračka

Návod

Parkside IAN 281479 Zváračka

Návod

Parkside PFDS 33 B2 Zváračka

Návod

Parkside PMPS 200 B1 Zváračka

Návod

Parkside IAN 389215 Zváračka

Návod

Parkside PFDS 33 B3 Zváračka

Návod

Parkside IAN 409152 Zváračka

Súvisiace kategórie