Návod Parkside IAN 409145 Zváračka

Návod

GB/IE/NI/CY/MT

15

z Environment with increased electrical hazard

When welding in environments with increased electrical hazard, the

following safety instructions must be observed.

Environments with increased electrical hazard may be encountered,

for example:

 In workplaces where the space for movement is restricted, such

that the welder is working in a forced posture (e.g.: kneeling,

sitting, lying) and is touching electrically conductive parts;

 In workplaces which are restricted completely or in part in terms

of electrical conductivity and where there is a high risk through

avoidable or accidental touching by the welder;

 In wet, humid or hot workplaces where the air humidity or sweat

significantly reduces the resistance of human skin and the insulating

properties or effect of protective equipment.

 Even a metal conductor or scaffolding can create an environment

with increased electrical hazard.

In this type of environment, insulated mats and pads must be used.

Furthermore gauntlet gloves and head protection made of leather or

other insulating materials must be worn to insulate the body against

Earth. The welding power source must be located outside the working

area or electrically conductive surfaces and out of the welder’s reach.

Additional protection against a shock from the mains current in the

event of a fault can be provided by using a fault-circuit interrupter,

which is operated with a leakage current of no more than 30 mA and

covers all mains-powered devices in close proximity. The fault-circuit

interrupter must be suitable for all types of current.

There must be means of rapid electrical isolation of the welding

power source or the welding circuit (e.g. emergency stop device)

which are easily accessible. When using welders under electrically

dangerous conditions, the output voltage of the welder must not be

greater than 113 volt when idling (peak value). Based on the output

voltage this welder may be used in these conditions.

z Welding in tight spaces

 When welding in tight spaces this may pose a hazard through

toxic gases (risk of suffocation).

 In tight spaces you may only weld if there are trained individuals

in the immediate vicinity who can intervene if necessary. In this

case, before starting the welding procedure, an expert must carry

out an assessment in order to determine what steps are necessary,

in order to guarantee safety at work and which precautionary

measures should be taken during the actual welding procedure.

Hodnotenie

Viac o tomto návode

Chápeme, že je pekné mať k svojmu Parkside IAN 409145 Zváračka papierovú príručku. Návod si môžete kedykoľvek stiahnuť z našej webovej stránky a vytlačiť si ho sami. Ak chcete mať originálnu príručku, odporúčame vám kontaktovať Parkside. Mohli by byť schopní poskytnúť originálny návod. Hľadáte príručku k svojmu Parkside IAN 409145 Zváračka v inom jazyku? Vyberte si preferovaný jazyk na našej domovskej stránke a vyhľadajte číslo modelu, aby ste zistili, či ho máme k dispozícii.

Technické údaje

Všetky príručky pre Parkside Zváračky
Ďalšie príručky od Zváračky

Často kladené otázky o Parkside IAN 409145 Zváračka

Náš tím podpory vyhľadáva užitočné informácie o výrobkoch a odpovede na často kladené otázky. Ak nájdete v našich často kladených otázkach nejakú nezrovnalosť, dajte nám o tom vedieť pomocou nášho kontaktného formulára.

Súvisiace produkty

Návod

Parkside IAN 409152 Zváračka

Návod

Parkside IAN 337263 Zváračka

Návod

Parkside PMSG 200 A1 Zváračka

Návod

Parkside IAN 494641 Zváračka

Návod

Parkside IAN 306962 Zváračka

Návod

Parkside IAN 286510 Zváračka

Návod

Parkside IAN 281416 Zváračka

Návod

Parkside PPS 40 B3 Zváračka

Súvisiace kategórie