SAFETY INSTRUCTIONS
Read the entire instruction manual before you start installation and
assembly and keep it for future reference.
1. Protect this device from water, humidity and other liquids. Avoid
using/storing it in extreme temperatures. Do not expose it to direct
sunlight and other sources of heat.
2. Protect this device from shock and being dropped.
3. Do not use the product for purposes dierent from displayed in this
operating manual.
4. Appliance for household use only.
5. Do not apply too much pressure on the device. Applying too much
pressure on the device will cause the rotating blade to stop. Reducing
pressure releases the blade.
6. Do not use the device on clothes you are wearing.
7. Do not use the device on damp clothes.
8. Exercise special caution when using the device near buttons, stitching,
zips, patches etc.
9. Keep the device out of the reach of children.
10. Use only specied batteries.
11. Use only authorized accessories.
12. Do not place the appliance in water or any liquid; nor handle/use it
with wet or moist hands.
13. Do not use this device if it has been damaged and malfunctions.
14. Do not attempt to repair this appliance yourself. In case of damage,
contact authorized service point for check-up or repair. Never
disassemble this device.
15. Clean and store this device in accordance to the instructions listed in
“Cleaning and storage” section.
PRODUCT DESCRIPTION
1. Blade guard
2. ON/OFF switch
3. Flu compartment
4. Battery compartment cover (cleaning brush on the inside of the cover)
①
②
③
④
BATTERY INSTALLATION
1. Press on the bottom of the battery compartment cover and remove it.
2. Insert 2x AA battery with correct polarization.
3. Replace the battery compartment cover and push it onto the device so
that it locks in place (you will hear an audible click).
Notes:
• Use only specied batteries.
• Do not mix batteries of dierent type.
• Replace all batteries at the same time.
• Store the device without the batteries inside if it is not going to be
used for a long period of time.
OPERATION
Notes:
• Before rst use make sure that all parts of the device have been
properly installed and the u compartment is empty.
• This lint remover can damage very soft materials. Therefore always test
the lint remover on an inconspicuous part of the garment.
• The device will not operate if the blade guard is not installed.
1. Lay the garment on a at surface such as an ironing board. Ensure that
the surface to be processed has no wrinkles. Otherwise, the garment
could be damaged.
2. Remove the protective guard.
3. Turn on the device by sliding the ON/OFF switch left.
4. Run the device lightly and without too much pressure over the
material.
5. Turn o the device by sliding the ON/OFF switch right.
6. Pull the u compartment to take it o the device. Throw away u
that have been collected inside the u compartment. Replace the
u compartment and push it onto the device until it locks in place
(you will hear an audible click).
7. After using the device, put the protective cover on the blade guard.
CLEANING AND STORAGE
• Do not place the appliance in water or any liquid.
• Do not use any chemical agents to clean this device.
• Clean this device with a soft, slightly damp cloth.
• Do not let the u compartment being overlled. If the u
compartment is overlled, the blade will work slowly even though
the batteries are still working. Regularly empty the u compartment.
Note: Blade is very sharp and can easily be damaged. Exercise special caution
when cleaning.
1. Make sure the device is switched o.
2. Unscrew the blade guard and remove the blade. Clean the blade and
blade guard with the included cleaning brush.
3. After cleaning, put the blade on the fan spindle and tighten the blade
guard.
• Before storing, make sure the device is clean and dry.
• Store the device in a dry, cool place out of the reach of children.
• Store the device with the protective guard on.
English
Correct Disposal of This Product
(Waste Electrical & Electronic
Equipment)
(Applicable in the European Union and other European countries with
separate collection systems) This marking shown on the product or its
literature, indicates that it should not be disposed with other household
wastes at the end of its working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, please
separate this from other types of wastes and recycle it responsibly to
promote the sustainable reuse of material resources. Household users should
contact either the retailer where they purchased this product, or their local
government oce, for details of where and how they can take this item for
environmentally safe recycling. Business users should contact their supplier
and check the terms and conditions of the purchase contract. This product
should not be mixed with other commercial wastes for disposal.
Made in China for LECHPOL ELECTRONICS Sp. z o.o. Sp.k.,
ul. Garwolińska 1, 08-400 Miętne.
EN
Zapojte sa do diskusie o tomto výrobku
Tu sa môžete podeliť o to, čo si myslíte o Teesa TSA0033 Odhrčkovač. Ak máte otázku, najprv si pozorne prečítajte návod. Vyžiadanie manuálu je možné vykonať pomocou nášho kontaktného formulára.