Návod Greenworks GD24CS Okružná píla

Návod

3. Remove the bolt and outer flange.

4. Use the lower guard lever to lift the lower guard and hold

the lever.

5. Remove the blade.

4 OPERATION

WARNING

Always wear eye protection.

WARNING

Do not use any attachments or accessories not

recommended by the manufacturer of this product.

4.1 START THE MACHINE

Figure 5

NOTE

The machine can not work until the lock-off Button is

pushed fully to the left or right. Do not operate the machine

at low speeds for extended periods of time.

1. Pull the trigger to turn the machine ON.

4.2 STOP THE MACHINE

Figure 5.

1. Release the trigger to stop the machine.

4.3 ADJUST THE CUTTING ANGLE

Figure 6.

1. Loosen the bevel lock knob.

2. Use bevel scale to set the necessary angle.

3. Tighten the bevel lock knob.

4.4 ADJUST THE CUTTING DEPTH

Figure 7.

1. Loosen the depth adjustment lever.

2. Raise or lower the base until the depth scale reaches the

required cutting depth.

3. Tighten the depth adjustment lever.

4.5 ADJUST THE CUTTING WIDTH

Figure 8.

1. Loosen the width adjustment knob to move the edge

guide to the necessary width.

2. Tighten the width adjustment knob after adjustment.

4.6 OPERATE THE MACHINE

Figure 9.

Kickback occurs when the blade stalls quickly and the

machine is driven back to you. A step which pinches the

blade in the wood can cuase blade stalling.

WARNING

To prevent kickback, release switch trigger immediately if

the blade stalls.

1. Keep the blade at the correct depth position.

2. Examine the workpiece for nails before you cut. Do not

saw into a nail.

3. Make straight cuts. Use a straight edge guide when rip

cutting. This helps prevent you twist the blade.

4. Use clean, sharp, and correctly set blades. Do not make

cuts with blunt blades.

5. Support the workpiece correctly before you begin a cut.

6. Use stable pressure when you make a cut. Do not force a

cut.

7. Do not cut warped or wet lumber.

8. Hold the saw tightly with the two hands and keep your

body in a balanced position to against the forces if

kickback occurs.

5 MAINTENANCE

CAUTION

Do not let brake fluids, gasoline, petroleum-based materials

touch the plastic parts. Chemicals can cause damage to the

plastic, and make the plastic unserviceable.

CAUTION

Do not use strong solvents or detergents on the plastic

housing or components.

WARNING

Remove the battery pack from the machine before

maintenance.

5.1 CLEAN THE MACHINE

CAUTION

The machine must be dry. Humidity can cause risks of

electrical shocks.

• Clear the unwanted material out of the air vent with a

vacuum cleaner.

• Do not spray the air vent or put the air vent in solvents.

• Clean the housing and the plastic components with a

moist and soft cloth.

6 TECHNICAL DATA

Voltage 24 V

5

English

EN

Hodnotenie

Viac o tomto návode

Chápeme, že je pekné mať k svojmu Greenworks GD24CS Okružná píla papierovú príručku. Návod si môžete kedykoľvek stiahnuť z našej webovej stránky a vytlačiť si ho sami. Ak chcete mať originálnu príručku, odporúčame vám kontaktovať Greenworks. Mohli by byť schopní poskytnúť originálny návod. Hľadáte príručku k svojmu Greenworks GD24CS Okružná píla v inom jazyku? Vyberte si preferovaný jazyk na našej domovskej stránke a vyhľadajte číslo modelu, aby ste zistili, či ho máme k dispozícii.

Technické údaje

Všetky príručky pre Greenworks Okružné píly
Ďalšie príručky od Okružné píly

Často kladené otázky o Greenworks GD24CS Okružná píla

Náš tím podpory vyhľadáva užitočné informácie o výrobkoch a odpovede na často kladené otázky. Ak nájdete v našich často kladených otázkach nejakú nezrovnalosť, dajte nám o tom vedieť pomocou nášho kontaktného formulára.

Súvisiace produkty

Návod

Graphite 58G493 Okružná píla

Návod

Skil 5820 AA Okružná píla

Návod

Ryobi LSC-180 Okružná píla

Návod

Ryobi EWS1366 Okružná píla

Návod

Ryobi RWS1250 Okružná píla

Návod

Fieldmann FDUK 50301 Okružná píla

Návod

Parkside IAN 326393 Okružná píla

Návod

Parkside IAN 289755 Okružná píla

Súvisiace kategórie