Návod Vivanco UR 2 Diaľkový ovládač

Návod

UR Universal Controller

Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: hotline@vivanco.de 1

( GB ) Operating Instructions -> 1

( D ) Bedienungsanleitung -> 2

( F ) Notice d'emploi -> 3

( E ) Instrucciones de uso ->5

( I ) Istruzioni per l’uso->6

( NL ) Gebruiksaanwijzing -> 8

( PL ) Instrukcja obsługi -> 9

( P ) Instruções de operação -> 10

(DK) Betjeningsvejledning -> 12

(S) Bruksanvisning -> 13

(RUS) Руководство по эксплуатации ->14

(GR) Οδηγίες χρήσης->16

(TR)

Kullanma talimatı -> 18

(CZ)

Návod k obsluze -> 19

(SK) Návod na obsluhu-> 20

(H) Kezelési utasítása -> 22

(GB) Instructions

Inserting the batteries

Open the battery flap on the back of the remote

control, press the tongue lightly downwards,

then insert 2 alkaline AAA batteries. Check that

the polarity markings on the batteries and in the

battery compartment are correctly lined up

(+=+), then close the flap carefully. – Always

use undamaged batteries.

Adapting to a device (e.g. TV or DVB Set

Top Box (or SAT/Cable) etc.

In order to control e.g. your TV or DVB you

must adapt or set the remote control to it. There

are two ways of doing so: direct control code

entry or code search.

If your UR does not understand you it blinks

and you can then repeat the entry. Each

understood entry is confirmed by LED blinking

briefly.

Direct control code entry using the enclosed

list

Example: setting to control a Panasonic

television set:

1. The enclosed list gives, for example, the

Panasonic Code 153.

2. To prepare code entry, briefly press the

SET button, and then the TV-button, until the

Powerkey lamp/LED lights constantly.

3. Then press the number buttons (e.g. 1 5

3) in sequence.

4. Once the numbers have been entered the

button lamp goes out and the remote control is

ready to control your appliance.

5. Finally, test the control code setting by

trying to control your television set. If it does not

work at all or not correctly try a different code

from the list or the code search (see below).

Code search

If the brand of your appliance is not in the list or

none of the codes given fits, we recommend a

code search.

Manual code search

1. Switch on the appliance to be controlled.

Program is running.

2. To prepare the code search, briefly press

the SET button and then additionally a

appliance button, e.g. the TV or DVB button,

until the lamp (LED) lights constantly.

3. Then point the remote control at the

appliance to be controlled.

4. Briefly press the ON/OFF

(appliance on/off) button once. The lamp (LED)

blinks.

5. Press the ON/OFF

(appliance

on/off) button repeatedly, approx. every second,

until appliance, reacts. - If you notice the

reaction of your appliance too late and the next

code has already been emitted you can go back

by pressing SET and then ON/OFF again. If

your appliance has switched itself off you must

switch it back on again, e.g. on the appliance or

with the original remote control, to continue

searching. - When your appliance reacts you

can also try out other buttons without

interrupting the search. If some buttons do not

work properly, simply continue searching with

ON/OFF.

6. When your appliance reacts correctly,

press the appliance button e.g. TV and end the

search. The lamp (LED) goes out.

- The search stops after approx. 30 seconds of

inactivity.

Automatic code search

Your remote control finds the correct settings

almost automatically in seconds:

1. Switch on the appliance to be controlled

so that you can watch a TV program.

2. To start the code search, press the SET

button, and then additionally the appliance

button e.g. TV or DVB, for more than 3

seconds until the Power-key lamp (LED) starts

to blink.

3. Then point the remote control at the

appliance to be controlled while the remote

control emits a different ON/OFF signal every 2

seconds.

4. When your appliance reacts, press any

button, except SET, to end the search. – If you

ended the search too late, continue to search

using the Manual Code Search (see above).

5. Finally, test the control code setting by

trying to control your appliance. If it does not

work correctly, please try the code search

again. The code search then begins with the

next code in the sequence. - Remember to

switch your appliance back on again if you wish

to continue searching.

Hodnotenie

Viac o tomto návode

Chápeme, že je pekné mať k svojmu Vivanco UR 2 Diaľkový ovládač papierovú príručku. Návod si môžete kedykoľvek stiahnuť z našej webovej stránky a vytlačiť si ho sami. Ak chcete mať originálnu príručku, odporúčame vám kontaktovať Vivanco. Mohli by byť schopní poskytnúť originálny návod. Hľadáte príručku k svojmu Vivanco UR 2 Diaľkový ovládač v inom jazyku? Vyberte si preferovaný jazyk na našej domovskej stránke a vyhľadajte číslo modelu, aby ste zistili, či ho máme k dispozícii.

Technické údaje

Všetky príručky pre Vivanco Diaľkové ovládače
Ďalšie príručky od Diaľkové ovládače

Často kladené otázky o Vivanco UR 2 Diaľkový ovládač

Náš tím podpory vyhľadáva užitočné informácie o výrobkoch a odpovede na často kladené otázky. Ak nájdete v našich často kladených otázkach nejakú nezrovnalosť, dajte nám o tom vedieť pomocou nášho kontaktného formulára.

Súvisiace produkty

Návod

Vivanco UR 4 SL Diaľkový ovládač

Návod

Vivanco UR 03 UF Diaľkový ovládač

Návod

Vivanco UR 14 Diaľkový ovládač

Návod

Vivanco UR 82 SE Diaľkový ovládač

Návod

Vivanco UR 40 USB Diaľkový ovládač

Návod

Vivanco UR 81 Diaľkový ovládač

Návod

Vivanco UR Zap 2 Diaľkový ovládač

Návod

Thomson ROC1128PAN Diaľkový ovládač

Súvisiace kategórie