Návod EMOS E8737 Meteostanica

Návod

3

J – DCF signal reception icon

K – alarm and snooze icon

L – current time

Press button Hold button

SNZ activates alarm snooze/display backlight

TIME displays year setting the time

ALM displays alarm time setting the time of alarm

CH sensor No. search for sensor 1, 2, 3

UP 1 step forward, alarm activation displays temperature units °C/°F

DOWN 1 step back search for DCF signal

Wireless sensor

Front side

A – outdoor temperature

B – sensor channel number, signal transmission icon

C – outdoor humidity, battery low icon

Back side

°C/°F – temperature unit

CH – switching between sensor channel numbers (1, 2, 3)

Putting into operation

1. Insert batteries into the weather station (3×1.5 V AAA), connect the 4.5V AC adapter and then insert batteries into the

wireless sensor (2×1.5 V AA).

When inserting the batteries make sure the polarity is correct to avoid damaging the weather station or sensor. Only use

alkaline batteries of the same type, do not use rechargeable batteries.

2. Place the two units next to each other. The weather station detects the remote sensor signal within 3 minutes. If the remote

sensor signal is not detected, press and hold the CH button to repeat search for the remote sensor signal.

3. If the outdoor temperature value disappears from the display, repeat steps 1 and 2.

4. We recommend placing the sensor on the north side of the house. The range of the sensor may decrease substantially in

urban areas. The sensor is resistant to dripping water, however, it should not be exposed to rain permanently. Do not place

the sensor on metal objects as this reduces transmission range.

5. If low battery icon is displayed, replace batteries in the sensor or weather station.

Switch-over to another channel and connecting more sensors

1. Press repeatedly the CH button on the back side of the weather station to select the required sensor channel – 1, 2 or 3.

Then press and hold the CH button; the

icon starts ashing.

2. Remove the cover from the battery compartment and insert batteries (2×1.5 V AA).

3. Press repeatedly the CH button to set the desired sensor channel No. – 1, 2, 3 which will be shown on the front panel display.

Data from the sensor will be loaded on the station display within 3 minutes.

4. Repeat the whole procedure if the sensor signal is not detected.

Radio controlled clock (DCF77)

After registering with the wireless sensor, the weather station will automatically start searching for the DCF77 signal for 10

minutes; the

icon is ashing. During the search, no other data on the display will be updated and the buttons will be disabled.

Signal detected – the icon stops ashing and the current time is displayed.

Signal not detected – the icon disappears.

Press and hold the DOWN button to repeat search for the DCF77 signal.

Press shortly the DOWN button again to stop search for the DCF77 signal.

DCF signal will be synchronised daily between 2:00 and 3:00 am.

In normal conditions (at a safe distance from sources of interference, such as television sets or computer

monitors) the detection of time signal takes several minutes. If the weather station does not detect the signal, follow these steps:

1. Move the weather station to another location and try to detect the DCF signal again.

2. Check the distance of the clock from the sources of interference (computer monitors or television sets). It should be at

least 1.5 to 2 m during the reception of the signal.

3. When receiving DCF signal, do not put the weather station to the proximity of metal doors, window frames and other metal

structures or objects (washing machines, dryers, refrigerators etc.).

4. In reinforced concrete structures (cellars, high-rise buildings etc.), the DCF signal reception is weaker, depending on the

conditions. In extreme cases, place the weather station close to a window toward the transmitter.

Reception of the DCF 77 radio signal is aected by the following factors:

• thick walls and insulation, basements and cellars

• inadequate local geographical conditions (these are dicult to assess in advance)

• atmospheric disturbances, thunderstorms, electrical appliances with no interference elimination, television sets and com-

puters located near the DCF receiver.

Hodnotenie

Viac o tomto návode

Chápeme, že je pekné mať k svojmu EMOS E8737 Meteostanica papierovú príručku. Návod si môžete kedykoľvek stiahnuť z našej webovej stránky a vytlačiť si ho sami. Ak chcete mať originálnu príručku, odporúčame vám kontaktovať EMOS. Mohli by byť schopní poskytnúť originálny návod. Hľadáte príručku k svojmu EMOS E8737 Meteostanica v inom jazyku? Vyberte si preferovaný jazyk na našej domovskej stránke a vyhľadajte číslo modelu, aby ste zistili, či ho máme k dispozícii.

Technické údaje

Všetky príručky pre EMOS Meteostanice
Ďalšie príručky od Meteostanice

Často kladené otázky o EMOS E8737 Meteostanica

Náš tím podpory vyhľadáva užitočné informácie o výrobkoch a odpovede na často kladené otázky. Ak nájdete v našich často kladených otázkach nejakú nezrovnalosť, dajte nám o tom vedieť pomocou nášho kontaktného formulára.

Súvisiace produkty

Návod

EMOS E8825 Meteostanica

Návod

EMOS ES5001 Meteostanica

Návod

EMOS E5005 Meteostanica

Návod

EMOS E6016 Meteostanica

Návod

EMOS E8468 Meteostanica

Návod

EMOS E0352 Meteostanica

Návod

EMOS E5018 Meteostanica

Návod

EMOS E0300 Meteostanica

Súvisiace kategórie